AWCY E43-48-48x Full Release torrent

▄▄▄·▄▄▄ ▄▄▄ . ▄▄▌ ▐ ▄▄▄▄ . ▄▄· ▄▄▌ ▄· ▄▄▄▄ ▄▄▄▄▄
▐█ ▀█▀▄ █▀▄.▀· ██· █▌▐▀▄.▀· ▐█ ▌▪ ▪ ██• ▐█▪██▀▄.▀•██
▄█▀▀█▐▀▀▄▐▀▀▪▄ ██▪▐█▐▐▐▀▀▪▄ ██ ▄▄▄█▀▄ ▄█▀▄██▪ ▐█▌▐█▐▀▀▪▄▐█.▪
▐█ ▪▐▐█•█▐█▄▄▌ ▐█▌██▐█▐█▄▄▌ ▐███▐█▌.▐▐█▌.▐▐█▌▐▌ ▐█▀·▐█▄▄▌▐█▌·
▀ ▀.▀ ▀▀▀▀ ▀▀▀▀ ▀▪▀▀▀ ·▀▀▀ ▀█▄▀▪▀█▄▀.▀▀▀ ▀ • ▀▀▀ ▀▀▀
██████╗
╚════██╗
▄███╔╝
▀▀══╝
██╗
╚═╝

-*- Are We Cool Yet? Presents -*-

###############################################################################
# #
# The Everyman's 43x (E43, E43x, E48) #
# A beginners printable pistol frame #
# v1.0 #
# #
###############################################################################
# /X> Release Notes <X\ #
###############################################################################
# #
# Second AWCY release! #
# #
###############################################################################
# /X> Credits <X\ #
###############################################################################
# #
# [-+ Brought to you by +-] #
# #
# ︻╦╤─ Sigfried(Co-developer, primary 43x/48) ─╤╦︻ #
# ︻╦╤─ 4myright(Co-developer, primary 43) ─╤╦︻ #
# ︻╦╤─ bitplumb(Head test engineer) ─╤╦︻ #
# #
# [-+ With the help of +-] #
# #
# Engarm(ongoing auto sear development assistance), #
# Because2nd(OEM measurements), All4one(Early CAD help), #
# and v8vtwin(Moral Support) #
# #
# [-+ Additional thanks to +-] #
# #
# Skyraze, Karver, Soggyknee, handydandy, all_i_no_is_gloc, mr_380_EZ, #
# apophis9x19, [REDACTED], #
# #
# and the entire Are We Cool Yet? team #
# #
###############################################################################
# /X> Print Settings <X\ #
###############################################################################
# #
# Filament: PLA+ or stronger #
# Temp: 205-225 (PLA) #
# Frame orientation: Print magazine well down. #
# Infill: 99% (gyroid pattern with tree supports preferred) #
# #
###############################################################################
# /X> Materials <X\ #
###############################################################################
# #
# 1x SS80 builders kit including: #
# This can be gotten from glockstore.com #
# #
# 1x combo front rail block #
# #
# 1x single piece rear rail #
# #
# 1x 4mm trigger pin #
# #
# 1x 3mm rear rail pin #
# #
# 1x Glock 43/43x/48 parts kit including: #
# #
# 1x barrel #
# #
# 1x upper parts kit #
# #
# 1x lower parts kit #
# #
###############################################################################
# /X> Linked Guides <X\ #
###############################################################################
# #
# Hans Grabber builds a Glock #
# #
###############################################################################
# /X> Assembly <X\ #
###############################################################################
# #
# [-+ Frame +-] #
# #
# 1. Remove supports, taking care to clean out the sear pocket. #
# #
# 2. Check that all rails and pins fit. Ream out holes if required. #
# #
# 3. Install mag catch spring and mag catch. #
# #
# 4. Install the rear rail. #
# #
# 5. Install sear housing and trigger. Make sure all holes align #
# properly with the frame. #
# #
# 6. Install the last round hold open lever. #
# #
# 7. Place the front rail into the frame. #
# #
# 8. Drive the 4mm pin through the front rail, last round hold open, and #
# trigger. (It can help to align these three components with a #
# smaller pin before driving through the 4mm pin.) #
# #
# 9. Drive the 3mm pin through the rear rails and sear housing. #
# #
# 10. Install the takedown bar and spring in front of the combo rail. #
# #
# 11. Install a the slide, and rack the slide numerous times to ensure #
# function and ensure the rails are firmly seated. #
# #
# 12. So anyway, get to blasting. #
# #
###############################################################################
# /X> Statistics <X\ #
###############################################################################
# #
# Combined round count from beta: 2195 #
# #
# Max round count on one frame: 600 (4myright) #
# #
# Max round count with different materials: #
# #
# Nylonx: 600 and counting #
# #
# Resin: 300 and counting #
# #
# PLA+: 215 and counting #
# #
# (give us a break theres an ammo shortage) #
# #
###############################################################################
# /X> Troubleshooting <X\ #
###############################################################################
# #
# Issue: Slide does not rack cleanly, or hangs up on the front of the #
# frame. #
# #
# Solution: The SS80 rails have notoriously bad QC. Check your rails for #
# flatness and squareness. If that does not resolve the issue, check the #
# frame for warp. Even the slightest warp in the sear will result in #
# difficultly cycling. #
# #
# Issue: Mag catch does not allow the removal of OEM mags. #
# #
# Solution: Make sure you have printed the OEM mag catch, not the shield #
# mag catch. The printed Shield catch has a larger contact area to insure #
# retention and is not OEM compatable. #
# #
# Issue: I have assembled the pistol and am not cool yet. #
# #
# Solution: Being cool is about the journey, not the destination. #
# #
###############################################################################
# #
# -`-,-{@ AWCY? - Stronger Together @}-,-`- #
# (oven appreciation group) #
# Join us at: https://www.AreWeCoolYet.WTF #
# #
###############################################################################